Product Categories

 

 


DIAL INDICATOR STAND

This tool is useful for testing spindle run out of machine tools, lathe work etc. It is well adapted for inspection of the parallelism of surfaces. The indicator can be swiveled in all directions. The base is of steel and provided With T slots for convenience in clamping. The surfaces of the base are accurately ground. New clamping System ensures quicker rigid clamping even with moderate tightening. The holder for the Dial Indicator is equipped with fine adjustment device permitting vibration free adjustment to zero.

SPECIFICATIONS:

KM – 300

LENGTH OF BASE 250 mm

WIDTH OF BASE 50 mm

HEIGHT OF BASE 35 mm

HEIGHT OF COLUMN 225 mm

DIAMETER OF COLUMN 18 mm

 

HEAVY DUTY DIAL INDICATOR STAND

(With fine adjustment)

This extra heavy and ruggedly made universal testing stand is used wherever the highest accuracy is required in using a comparator. It can be used in many different ways; on the surface plate in testing parallel surfaces of work pieces on machine tools for setting up pieces to be machined with reference to already existing surfaces or for inspecting mounted pieces for run-out etc.

The surfaces of the H-formed base, the column and the extension arm are high precision ground. The column can be moved and clamped in any position of the base with a knurled nut.

The extension arm, which can be adjusted in height moved lengthwise and swiveled is sufficiently rigid that vibrates during the measurement even with the fullest extension are at a minimum.

The base of the indicator stand is made of steel or cast iron.

SPECIFICATIONS:

KM - 301

HEIGHT OF COLUMN
300 mm 500mm800m

MAXIMUM

HORIZONTAL

EXTENSION 350 mm 350 mm 350 mm

LENGTH OF BASE 300 mm 300 mm 300 mm

WIDTH OF BASE 100 mm 100 mm 100 mm

DIAMETER OF COLUMN 40 mm 40 mm 40 mm

EXTENSION ARM 25 mm 25 mm 25 mm

 

LEVER TYPE DIAL INDICATOR

RH – AM  

 

RH – BH 
CH – CM
DTH – M  
KJH – D
RH – B                    
CH – C  
DTH               

 

Rectangular Holder type AM 8 mm*4.8 mm pin diameter 4 mm.
Rectangular Holder Type BM 13 mm*6mm, pin diameter 4 mm.
Cylinder Holder Type CM 9.5 mm diameter, pin diameter 4 mm.
Swivel Clamp with Dovetail Holder (Metric models) Bore diameter 4 – 9.5 mm.
Knuckle Joint Holder (Dovetail).
Rectangular Holder Type A 5 / 16 “ * 3 / 16,pin diameter 1 / 4 “
Cylindrical Holder Type C 3 / 8 “ diameter pin diameter 1 / 4 “.
Swivel Clamp with Dovetail Holder (Inch models) Bore diameter 1/4–3/8 ”.

 

 

 

 

 

 

 

 

COMPLETE SET           SPECIFICATIONS CONSISTS OF   

Tool post holder                                  9.5 * 19 * 150
Upright spindle                                    8 dial * 115 L
Universal Clamp                                 6.5 and 8 holes
G – Clamp                                          33 capacity round or flat


Extra contact points With Domed Anvil and Round Anvil Tommy bar. Hole attachment with indicator Mounting hole and swivel Arm 9.5 hole for dial indicator.


                    TYPE        READING    TRAVEL            GRADUATION
40 mm             787-1     0.001 mm       3.5 mm                 0-50-0
Black               787-2     0.001 mm       3.5 mm                 0-100
Plunger
Type                787-3     0.001 inch       0.14 inch              0-25-0
Dial           

Gauges            787-4     0.001inch       0.14 inch              0-50

 

Copyright ©2014 Shreepad Industries